§ 35-1903 — Residential design standards
Code of the City of Chandler (Supp. No. 80: codified through Ordinance No. 5171, adopted July 13, 2026) · Chandler City Code § 35-1903
Corpus is an independent public-information project, not the official City of Chandler website. Stable reference: corpuslaw.us/code/10c43f99-c35f-4cbd-bc0f-a407964b3876
35-1903. - Residential design standards.
(1) Applicability: (a) The following objective design standards shall be applied to i) all new single-family homes, duplexes, triplexes and fourplexes, developed individually or as part of a subdivision; and ii) multi-family residential developments. (b) These standards are intended to ensure that new single-family residences, middle housing developments, and multi-family developments promote a high-quality living environment by identifying minimum aesthetic and functional requirements that align with policies in the Chandler General Plan. These include creating a sense of place, a desirable streetscape appearance, and walkable neighborhoods with access to parks, commercial areas, and community facilities. (2) Site layout: (a) Height and area regulation for individual lots: Height, building setbacks, minimum lot size, and maximum lot coverage are regulated by the zoning district in which the property is located. These standards can be found in the respective sections of the City of Chandler Land Use and Zoning Code as follows: Zoning Districts | Code Section Agricultural District (AG-1) | 35-403 Single-Family District (SF-33) | 35-503 Single-Family District (SF-18) | 35-603 Single-Family District (SF-10) | 35-603.1 Single-Family District (SF-8.5) | 35-703 Medium-Density Residential District (MF-1) | 35-803 Multiple-Family Residential District (MF-2) | 35-903 High-Density Residential District (MF-3) | 35-1003 Middle Housing Overlay District | 35-3503 Height and area regulations for lots located in Planned Area Development (PAD) zoning districts are established by the ordinance that adopted the PAD, which can be found in the development's zoning file. Zoning files are kept at the City of Chandler's Development Services Department. (b) Site layout design standards applicable for single-family lots, single-family subdivisions, duplex, triplex, fourplex, and multi-family (five (5) units or more) shall be as indicated in the following table with a "X." Site Layout Design Standards | Single-Family (1—7 Lots) | Single-Family with 8 or More Lots | Duplex, Triplex, and Four-Plex | Multi-Family (5—20 Units) | Multi-Family (20 and Up) 1. Project arrival: The primary entrance where a street or driveway intersects an arterial or major collector shall include a minimum of three of the following: a. Monument sign b. Enhanced landscaping with 15% more landscaping than what is required c. Specialty pavement for a non-gated community for a minimum of 50 ft in length measured from the public right-of-way. d. Specialty pavement for a gated community shall be provided measured from the public right-of-way to 30 feet beyond the call box. e. Architectural tower or other similar architectural feature f. Boulevard style entry with a landscaped median for a minimum of 50 ft in length from the property line | X | X 2. Project theme: Each development shall provide a distinctive project theme consistently throughout the site, consisting of: a. Distinctly designed walls for the project theme wall b. Specialized fencing when fencing is proposed; details of accent walls with two or more materials when accent walls are proposed c. Specialized pedestrian and/or vehicular gates when such gates are proposed d. A project specific plant palette | X | X | X 3. Provide a continuous pedestrian circulation system on at least one side of the primary drive aisle(s) and/or around the entire site connecting buildings, ground-floor residential units, amenities, parking, and adjacent streets. If there is an adjacent public amenity such as a park, then a pedestrian pathway shall connect the development to the park where permissible by the City. | X | X | X 4. Common open space areas in multi-family projects shall be provided as follows: a. Usable common open space and recreation area at the rate of 150 square feet per bedroom. Such area must be at least 20 feet wide and shall not be encumbered by nonrecreational improvements. All open space area for community play shall be centrally located and not adjacent to refuse areas. | X | X 5. Each development shall provide amenities in accordance with the following schedule: | X | X [image omitted; see the official code] 6. Amenity options include but shall not be limited to: a. Swimming pool, a portion of which shall be a minimum 60-foot length, with cool deck perimeter and ramada. b. Jacuzzi area with ramada. c. Ramada with bbq and seating areas. d. Tot lot. e. Volleyball court. f. Concrete multi-use court. g. Tennis courts, pickleball and/or racquetball courts. h. Weight room. i. Dog park. j. Putting green. k. Walking path. 7. Location: a. Any multi-person activated outdoor amenities shall not be located closer than 100 feet from any existing neighboring residential property. 8. Excluded areas: The following shall not be counted towards common open space: a. Driveways or parking spaces. b. Required front, side, and rear yard setback areas. c. Non-functional landscaped areas such as street frontage landscaping, building foundation landscaping, and landscaping within the parking lot. 9. Open space reductions: a. The Zoning Administrator may reduce or waive the open space requirements if: i. The subject site is located within the Infill Incentive District, Middle Housing Overlay District, or within ¼ mile (travel path) of publicly accessible park or public recreation facility. 10. Private open space shall be provided for each unit. Such spaces shall have an unencumbered area that is a minimum of 65 square feet with a minimum width of 8 feet and a minimum depth of 5 feet and shall be entirely covered as required in subsection 3, building architecture. | X | X | X | X | X 11. View fencing shall be provided along arterial and collector streets in areas where private yards do not abut those streets, except for non-gated subdivisions, which may provide view fencing or leave the aforementioned areas open with no wall or fence. View fencing may include a combination of masonry and view fencing providing that at least the top 60% of the fencing is view fencing | X | X | X 12. If a gate is provided to the main entrance of a single-family subdivision or a multi-family complex, the gates shall not be located further towards the street than the closest building wall and shall not be made of a solid or opaque material. | X | X | X 13. Parking garages fronting a street shall be placed next to each other on adjacent lots in order to maximize on-street parking, where applicable. | X | X 14. For corner lots, parking garages shall be located on the interior lot side (not the street corner side). | X | X 15. Garages fronting onto an internal driveway or street shall be setback: a. 3—5 feet from said driveway or street, or b. A minimum of 20 feet from said driveway or street | X | X | X | X | X 16. A one-car garage or shade structure is required to be 10 ft by 20 ft of unencumbered space. A two-car garage or shade structure is required to be 20 ft by 20 ft of unencumbered space. Parking requirements are regulated by section 35-1804. | X | X | X | X | X 17. The required covered parking spaces shall be located adjacent to units, and the guest parking spaces shall be evenly dispersed throughout the development. | X | X 18. Provide screening or other accommodation for trash containers, recycling bins, household tools and equipment. | X | X | X (3) Building architecture: (a) Building architecture design standards applicable for single-family lots, single-family subdivisions, lots with a single duplex, triplex, or fourplex, and multi-family (five (5) units and up) shall be as indicated in the following table with a "X." Building Architecture Design Standards | Single-Family | Single-Family with 8 or More Lots | Duplex, Triplex, and Four-Plex | Multi-Family (5—20 Units) | Multi-Family (20 and Up) PRIMARY ENTRY DESIGN 1. The primary entrance shall be designed to include one of the following: a. Porch (a roof covered area attached to and projecting a minimum of six (6) feet from the front exterior wall of the structure covering the entrance and an extended area along the front for seating). b. Portico (a column supported roof over the entrance of the home that extends a minimum of 5 feet from the exterior wall to provide shelter from the elements). c. Awning (a roof covering that is not supported by columns and that is attached to and projects a minimum of 4 feet from the exterior wall and is located over the entrance to provide shelter from the elements. awnings shall be metal, roof tiles, shingles, or other hard non-flexible materials. d. Recess (a front door that is recessed a minimum of 4 feet from the exterior wall plane on which the door is located to create a covered landing area.) | X | X | X | X | X 2. Orient front doors toward the fronting street or a common courtyard that is shared with other dwelling units. The use of distinctive architectural elements and materials to denote prominent entrances is required. | X | X | X | X | X 3. Building orientation: Design the primary facade of the buildings with varied setbacks for a minimum of 5 feet in depth to create an interesting and attractive street edge while maintaining the required building setback. | X | X | X GARAGE PLACEMENT & ORIENTATION 4. Garages shall use colors and materials used on the primary building façade to blend the garage with the frontage of the dwelling. | X | X | X | X | X 5. When oriented as a side entry garage, a minimum of 25% of the surface area of the side of the garage facing the street shall include windows and architectural detailing to match the detailing on the primary portion of the structure and appear as a livable portion of the dwelling unit. | X | X | X MASSING & SCALE 6. If the front elevation is longer than 30 feet, incorporate a minimum of 2 feet deep by 10 feet wide offset for each 30 feet of building wall length and extend to the full height of the building. Building entrances and front porches may count towards meeting this requirement. | X | X | X 7. Horizontal off sets: Breaks in massing of at least 2 feet in depth shall be provided for a minimum of 25% of a single building elevation through the use of varying setbacks, building entries, building offset, or modulation of building facades. | X | X 8. Vertical variation: Change in rooflines of at least 2 feet in height shall be provided for a minimum of 25% of a single building elevation through change in height and form. 9. The Zoning Administrator may accept minor departures from the horizontal off set and vertical variation requirements for the rear elevations of a building that are not visible from public rights-of-way and adjoining residential, commercial, or open spaces. 10. Where the side façade at the end of a building is oriented to a street, driveway, or common Open space area, massing and level of detailing of the side façade shall be consistent with the front façade. articulation of the side façade may include windows, doors, and porches. | X | X 11. Side elevations shall provide a minimum of one horizontal plane break of at least 2 feet in depth. | X | X | X 12. Provide single-story or combination one- and two-story homes on all corner lots, with the two-story portion encompassing a maximum 75% of the building footprint and oriented furthest away from the street side yard. | X | X | X 13. For lots greater than 50 feet wide: No more than three detached two-story single-family homes shall be located next to each other along arterial and collector streets, except when: a. Rear yard setbacks are staggered a minimum depth of 10 feet every 150 feet or less, or b. Two-story homes have a single-story component that comprises at least 25% of the length of the building footprint and the two-story component is oriented furthest away from the arterial or collector street and which no more than three are located next to each other without staggering the rear yard setback a minimum of 10 feet or locating a two-story home that does not have a one-story component. | X 14. Structures that are two stories or more shall comply with a minimum of two of the following strategies to reduce massing and diminish a box-on-box appearance: a. Include a single-story element on the rear or front elevation that is at least 25% of the length of the building footprint. b. At least 3 sides of the structure provide a minimum of one vertical break stepping back a minimum depth of 3 feet for at least 25% of the length of each side. c. Provide multiple roofs at different heights, or parapet heights varying a minimum of 2 feet. d. Provide at least 3 of the following features that break up the box-on-box effect: i. Covered rear patios (minimum 4 feet in depth) extending from the exterior wall of the structures. ii. Covered porches (minimum 6 feet in depth) shall run at least 50% of the front of the structure for homes that are 40 feet or wider. for homes 39 feet wide or less, the covered porch (minimum 6 feet in depth) shall run at least 30% of the front of the structure. iii. Bay windows iv. Cantilevers v. Projecting balconies (minimum 4 feet in depth) vi. Dormers vii. Awnings (minimum 4 feet in depth) | X | X | X ROOFLINES 15. Variation of roof forms shall be used on buildings over 50 feet in length along the street frontage and accomplished through the use of differences in roof height (minimum 2 feet) and/or form. | X | X | X 16. Varied roof form shall be used as appropriate to the architectural style, including but not limited to the following: Hipped roofs, shed roofs, gabled roofs, varying pitches, roof dormers, and flat roofs. | X | X | X | X | X 17. Rooflines shall be designed with changes in ridgeline direction and configuration to ensure variation in rooflines between structures. | X | X | X | X | X 18. No more than two identical side-by-side roof slopes should be constructed along arterial or collector streets or public open space. | X | X ARCHITECTURAL DIVERSITY & ARTICULATION 19. New developments with 4 or more contiguous single-family detached lots shall offer multiple distinctly different architectural styles as follows: | X | X [image omitted; see the official code] Each architectural style shall feature at least four (4) distinctive features on each elevation, such as but not limited to: a. Roof form and materials b. Masonry veneer (covering a minimum 20% of the elevation) c. Exterior materials d. Window and column detailing e. Arches f. Ornamental ironwork g. Eave details 20. A multi-family development must have at least one clearly defined architectural style, and each architectural style shall feature at least four distinctive features on each elevation, such as but not limited to: a. Roof form and materials b. Masonry veneer (covering a minimum 20% of the elevation) c. Exterior materials d. Column detailing e. Arches f. Ornamental ironwork g. Eave details | X | X | X 21. A minimum of three different materials and at least five of the following architectural elements shall be provided on each building elevation: i. Covered porch ii. Bay windows iii. Cantilevers iv. Projecting balconies v. Dormers vi. Awnings vii. Trims around doors and windows that match the architectural style viii. Window mullions and muntins ix. Window shutters x. Accent materials (e.g., decorative tile, decorative metal accents) xi. Decorative brackets under roof eaves, projecting balconies, or other xii. Decorative downspouts | X | X 22. Duplexes, triplexes, fourplexes shall be designed to appear as separate units by the use of clearly identified entries. | X | X 23. All primary entrances into residential buildings or individual units shall provide weather protection by having an overhead roof feature extending a minimum of four feet from the building façade and four feet in width. | X | X | X | X | X 24. The first floor shall provide pedestrian scaled elements by using two or more architectural features on the front elevations (e.g. arches, awnings, fenestration, patios, columns, cornices, moldings, and trellises) that are not used in the same pattern on the upper stories. | X | X 25. The same elevation shall not be built side-by-side or directly across the street from one another as defined by 60% or more of lot width. | X | X | X MATERIALS & COLORS 26. All exterior materials shall be durable to withstand the elements such as but not limited to brick, masonry, stone, masonry veneers, concrete, composite wood products and stucco. | X | X | X | X | X 27. A unified palette (color, texture, sheen) of materials shall be used on all sides of buildings. Every building shall include no less than three colors appearing on the building exterior. | X | X | X | X | X 28. Natural materials such as stone, river rock, and slate, which are intended to be seen in their natural state shall not be painted. | X | X | X | X | X 29. Roofing materials shall consist of the following: Dimensional composite shingles, ceramic tile, clay tile, concrete tile, and standing seam metal. Wood shingles are prohibited. | X | X | X | X | X 30. Untreated wood is not permitted. | X | X | X | X | X 31. When a material wraps around a corner it shall be terminated by an architectural element such as an offset, column, intersecting wall, or fence. | X | X | X | X | X 32. Balcony design shall match the building in terms of style, color, and materials. | X | X | X | X | X
(Ord. No. 5142, § 2(Exh. A), 11-13-25)
Ask a question about Chandler law
Corpus searches the Chandler sections it holds and shows the ones that match, with their citations. Free, no sign-in.
