PF-1 (Public Facilities - Low Intensity) district.
Round Rock Zoning and Development Code, art. V, § 2-56
in effectSec. 2-56. - PF-1 (Public Facilities - Low Intensity) district.
(a) Purpose. To establish and preserve areas of low intensity land use primarily devoted to places of worship and other public uses.
(b) Permitted uses. Uses permitted in the PF-1 district may be found in Sec. 2-60.
(c) Lot and building dimensional standards. Property and buildings in the PF-1 district shall conform to the standards found in Sec. 2-61, with the following supplementary notes:
(1) Additional setback requirement. All uses which contain structures in excess of 20 feet in height and which also abut SF (Single-Family) or TF (Two-Family) zoned property, shall be required to meet the following additional setback requirement: for each one foot of height in excess of 20 feet, the structure shall be set back from said abutting property line one extra foot in addition to the minimums set forth in the lot and building dimensional standards in Sec. 2-61.
(2) Additional height requirement. Places of worship buildings, gyms, or auditoriums shall have a maximum height of 70 ft. provided they do not contain more than two stories.
(d) Supplementary development standards. In addition to the standards found in chapter 8 of this Code, the following regulations apply to the PF-1 district:
(1) Light fixture height. The height of a light fixture shall not exceed 20 feet.
(e) Public facilities - low intensity design standards. The following design standards apply to all buildings in the PF-1 district. These standards are intended to ensure an attractive built environment in Round Rock. Selection of materials, color, building orientation, articulation, and windows shall reflect the design themes established in the neighborhood which the proposed development borders. Alternative designs may be approved in writing by the zoning administrator in order to implement a specific, recognized architectural style not accommodated by the design standards below, excluding corporate architecture. Additions to sites and projects with existing buildings may continue the design style that has been previously established.
(1) Exterior wall finish. The building materials of a project shall be durable, require low maintenance, and be of the same or higher quality as surrounding developments.
a. At least 50 percent of the exterior wall finish of all buildings shall be natural stone, simulated stone, or brick, except for doors, windows and trim.
b. Other materials allowed for the exterior wall finish are: stucco; fiber cement siding; architecturally finished steel or metal; glass with steel framing; or architectural concrete masonry units (CMU). These materials shall not comprise more than 50 percent of the total exterior wall finish (breezeways are not included in this calculation). However, 100 percent stucco may be permitted in conjunction with a tile roof. The use of materials other than those listed in this section and in subsection (e)(1)a, above, shall be limited to accent features.
c. Fiber cement siding shall not comprise more than 25% of the total exterior wall finish. Flat, unarticulated panels are prohibited.
d. Architectural CMU shall have an ashlar pattern.
(2) Exterior color. Day-Glo, luminescent, neon, or similar types of color finishes are prohibited.
(3) Glass. Mirrored glass with a reflectivity of 20 percent or more is prohibited on the exterior walls and roofs of all buildings and structures.
(4) Orientation requirements.
a. Building elevations that face a public street shall have at least 15 percent of the wall facing the street consist of windows and/or pedestrian entrance areas.
b. Main entrances shall be visible to pedestrians from the street or a public plaza on the primary frontage.
c. Buildings with multiple street frontages shall be designed with primary facades facing each public street.
(5) Building articulation. All buildings shall be designed to include varied relief to provide interest and variety and to avoid monotony. This shall include details that create shade and cast shadows to provide visual relief to the buildings. Horizontal and vertical elements of exterior walls should vary in height, design and projection to provide substantial architectural interest and style. A minimum of four (4) features from the following list shall be incorporated into the building design:
a. Arcades/colonnades.
b. Decorative cornices.
c. Eaves.
d. Offset in building elevation.
e. Variation of roof lines.
f. Arched and/or recessed entryway.
g. Arched windows.
h. Gable windows.
i. Oval or round windows.
j. Transom windows.
k. Stone coursing around windows.
l. Shutters.
m. Stone or brick accent wall.
n. Decorative stone or brick band.
o. Decorative tile or metal.
p. Awnings.
q. Canopies.
r. Storefronts.
s. Other feature as approved by the zoning administrator.
(6) Building elevation variation. The length of walls facing public streets shall be broken into smaller planes. Wall planes shall not extend more than an average of 35 feet without an offset or interruption by a pilaster or structural frames, change in roof line, or change in exterior wall finish.
(Ord. No. O-2019-0206, § III, 5-9-2019)
Source: City of Round Rock, Texas, Code of Ordinances (Municode Library, library.municode.com)URL: https://library.municode.com/tx/round_rock/codes/code_of_ordinances?nodeId=PTIIIZODECO_CH2ZODIUSRE_ARTVPUCIUSDI_S2-56PUFAOWINDIFetched: 11/16/2026
