§ 12-36-6 — Design regulations—Sign standards—General CBID sign standards
Memphis Code of Ordinances (Supp. No. 33: codified through Ordinance No. 5959, enacted May 12, 2026) · Memphis Code of Ordinances § 12-36-6
Corpus is an independent public-information project, not the official City of Memphis website. Stable reference: corpuslaw.us/code/4182ff39-ce07-4783-95aa-b8a38dc7a8d8
Sec. 12-36-6. - Design regulations—Sign standards—General CBID sign standards.
All signs in the CBID shall adhere to the following guidelines and size limitations except in cases where outstandingly creative design solutions are offered. In such cases, if a proposal incorporates unique or high quality materials (such as neon, hand painting, some metals, or well-crafted wood), exterior lighting (such as floodlighting), unique shapes, and outstanding graphic composition, a sign exceeding the limits stated in this chapter may be approved. All signs should, however, be appropriately scaled to fit their context, should complement the building on which they are located, and should not intrude upon any architectural detail. A. Identification. All signs within the CBID are encouraged to utilize creative approaches to property and business identification; however, signs should be used for identification only, not for the advertisement of services or products available within a building or site. The only exception to this is off-premises advertising. 1. Removal. When a business closes or relocates, its sign shall be removed within three months of the date of close. If the sign has not been removed after six months, the property owner will be notified that the sign is noncompliant and will be formally requested to remove the sign. Unless the owner can provide a reason acceptable to the design review board that the sign should be retained, the sign shall be removed immediately. If the sign has not been removed within one year of the close of the building or business, it can be removed by the city or the center city commission at the owner's expense. 2. Disrepair. When a sign (designated for identification or off-premises advertising) falls into disrepair or is abandoned, the CCC staff may notify the property owner that the sign is noncompliant and request that the sign be removed. Unless the owner can provide a reason acceptable to the design review board that the sign should be retained, the sign shall be removed immediately. If the sign has not been removed within one year following notification, it can be removed by the city or the center city commission at the owner's expense. B. Graphic elements. All signs should contain no more than ten graphic elements. 1. If a name of a business consists of more than four syllables, it is counted only as four graphic elements. 2. The property's legal street address shall only count as one graphic element. C. Number of signs. Any ground floor business is allowed two primary signs facing a public right-of-way; however, the area of the signs may not exceed the allowable size requirements as outlined in following sections. D. Upper floor tenants. Each ground floor leasable unit is considered separately for signage; however, upper floor tenants are not allowed signs at the ground level unless they have a separate entrance at the ground level fronting onto a public right-of-way. Upper floor tenants in all cases are allowed, as established below, window or door graphics on the ground level and window graphics at the floor on which they are located. E. Multitenant buildings. Multitenant buildings may incorporate a designation sign at the ground level that identifies all of its tenants. F. Size of signs. The size of a sign will be determined by the smaller of the following two measurements: (1) the area of a rectangle enclosing all elements of a sign, including any sign cabinet or edges of a cabinet; or (2) the sum total of all areas of all elements of a sign. G. Ground signs. Ground signs are freestanding elements, and include pole-mounted signs and shorter monument signs. Any activity that is set back from the street or public right-of-way by at least 35 feet may display one ground sign within the allowable size limits set forth below: 1. Pole signs shall be no taller than 20 feet and shall be no closer than 300 feet from any other pole sign. The size of the sign cabinet on top of the pole shall not exceed 45 square feet. 2. Monument signs shall not exceed 35 square feet. The height of a monument sign shall not exceed six feet. Monument signs should be designed and located so that they do not create security hazards or visual barriers to traffic. 3. Changeable copy signs of any type are not allowed. This includes individual cabinets as part of a pole sign or portable readerboard signs. H. Wall signs. Wall signs may be attached flat to or pinned away from the wall and may not project from the wall by more than 18 inches. In no case should a wall sign obscure architectural details, window openings, or other open areas within a building facade. 1. Any activity may display one wall sign on each side of the building that fronts onto a public right-of-way. 2. The size of an individual wall sign will be no more than 40 percent of the signable area of any building. 3. If an activity in a building of two or more stories is a place of entertainment, a place of assembly for 200 or more people, a hospital, a hotel, or a majority tenant of the building, a sign may be placed on the wall near the roof line. In such cases, there is generally an area near the roof that is free of architectural detail; this area will be considered the signable area and no sign should exceed 40 percent of that area. Such signs are not considered primary signs and therefore do not count against the size limitations of lower, primary wall signs. I. Projecting signs. Any activity may display one projecting sign on each public right-of-way frontage. A projecting sign may not extend above the roof of the structure to which it is attached. 1. Projecting signs shall be mounted at right angles to the building facade except if the building is a corner building. On corner buildings, a projecting sign may be mounted at a 45 degree angle to the building; however, in such cases, the sign at a 45 degree angle would be the only projecting sign allowed for the activity. 2. Projecting signs must clear the sidewalk by at least eight feet and shall project no more than four feet from the building face or one-third of the sidewalk width (whichever is less). Marquee graphics are excluded from this constraint. 3. The vertical axis of a projecting sign will be no more than 25 percent of the height of the building to which it is attached if the building is 75 feet tall or less, as shown in Exhibit 4 set out at the end of this section. If the height of the building to which the projecting sign is attached is greater than 75 feet, then the vertical axis of the sign cannot exceed 20 feet. The overall size of a projecting sign must adhere to Table 1 below. Table 1 Length of Frontage on Public Right-of-Way | Total Allowable Signage (square feet) Less than 30′ | 20 30′ to 49′ 11″ | 30 50′ to 69′ 11″ | 40 70′ to 99′ 11″ | 50 100′ and greater | 60 J. Above-roof wall signs. Wall signs above the roof are allowed only in three situations: on hotels, on hospital buildings, and when the tenant identified by the sign is a majority tenant within the building. 1. An above-roof wall sign may be attached to or pinned away from permanent portions of the building's structure that extend above what is traditionally considered to be the roofline of the building and may not project more than 18 inches from the wall to which it is attached. This type of sign should not extend above the highest projection of the roof, including elevator penthouses and mechanical enclosures. The size of the sign will be limited by the roof structure to which the sign is attached and will be no larger than 40 percent of its signable area. 2. Above-roof wall signs are allowed only on buildings that are taller than 50 feet in height. K. Rooftop signs. Signs above the highest projection of the roof are not allowed except as outlined in the standards for the ballpark district and Peabody Place entertainment district. L. Marquee signs. Marquees are allowed only on theaters, other entertainment establishments featuring live performances, and places of assembly of 200 or more people (including restaurants and bars). 1. As a permanent structure attached to and projecting from a building, a marquee is very much a part of a building's overall design and must be integrated into the facade design. A marquee can project the entire width of the sidewalk, assuming there are not obstructions, but must clear the sidewalk by at least eight feet. 2. Only individual letters or symbols should be placed on or attached to marquees. The area reserved for changeable copy should be no more than 85 percent of each side of a marquee. Changeable copy displayed on marquees is not included in the items of information calculation for the building or tenant. 3. If an activity is eligible for a marquee, it may not have any other projecting sign. M. Window signs. Permanent window signs shall be affixed to the window and limited to 25 percent of the total area of the window in which they are displayed. Temporary window signs shall be limited to 15 percent of the total window area. N. Designation signs. An industrial park, shopping center, or multitenant building can display a designation sign that indicates the name of multiple activities. These signs are subject to the above limitations regarding items of information and size. Designation signs shall not be taller than ten feet when a ground sign is allowed. Wall designation signs must adhere to the standards for wall signs. 1. Directional signage is allowed only for purposes of wayfinding and may not be used for advertising. 2. Directional signage must be kept to a minimum necessary to locate the intended destination. 3. The DRB will review all directional signage with regard to its integration with the overall signage package for the intended project. O. Directional signs. Directional signs do not count toward the allowable sign limit per activity. These signs can be vehicular or pedestrian oriented, but in no case, should they exceed a size of six square feet if oriented toward vehicles or three square feet if oriented toward pedestrians or a height of four feet. Directional signs should not be designed or situated as to provide a traffic or security hazard. In no case shall they be located within a public right-of-way. P. Off-premises advertising. Permitted off-premises signs fall within only one of two categories: wall painted signs and sponsored artwork. No other off-premises signs shall be permitted within the CBID. 1. Off-premises advertising attached to bus shelters and trolley kiosks is exempt from these standards. 2. Wall painted signs are allowed only in the following districts: South Main/warehouse, the Pinch, and Beale Street. Wall painted signs must be on the sides of buildings and must follow the guidelines and size restrictions for wall signs in subsection (F) of this section. When allowed, they are permitted only on buildings between two and 15 stories tall, not within 200 feet of any other wall painted off-premises sign and should not project from the face of the building wall. 3. A current certificate of use and occupancy is required before an off-premises identification sign can be installed. 4. When allowed, all off-premises wall signs must be hand painted unless the sign has been approved and designated by the design review board as sponsored art. 5. Sponsored artwork involves graphics which do not necessarily identify a particular product, place or event in their imagery; but include identification of a sponsor that may be a business enterprise or other entity; e.g., a private business may install a painted mural on the side of a building depicting a historic streetscape and include the name of its business as the provider of the mural. 6. For the purposes of these guidelines, sponsored art is considered to be only two-dimensional graphics or other types of signboards/sign cabinets; these standards are by no means intended to address three-dimensional sculpture or other types of artwork. 7. All sponsored art must adhere to size and placement guidelines outlined above regarding the particular type of artwork: wall art, projecting art, etc. The size of the identification of individual or group sponsors shall be limited to ten percent of the overall area of the piece of art. Q. Awnings. Awnings can greatly enhance the appearance of a building, can provide shade and shelter, and can provide an alternative means of tenant identification. As extensions of the building to which they are attached, they must be carefully considered for their appropriateness of design in relation to the building's architectural character. 1. Buildings of historic character should have awnings that respect and complement the architecture. Contemporary building designs may accept a wider range of awning styles. Buildings or storefronts with 19th or early 20th century facades should, typically, have simple, sloped awnings rather than curved or rounded awnings or one of more modern design. 2. Awnings should fit the openings of the building on which they are attached and not overlap the opening or multiple openings. 3. Awnings should not obscure any significant architectural detail such as ornamental metal, glass or woodwork. 4. Lettering on awnings can be placed on the vertical valance flap or on the sloped portion of the awning. Any lettering that is larger than three inches in height will be counted against the allowable amount of primary signage for the activity or property. In such cases, the area of the graphic will be determined by measuring the area of the smallest rectangle that encloses all of the elements of the graphic. The maximum signable area for awnings is 30 percent of the awning's face. 5. The recommended material for awnings shall be canvas, particularly on historic buildings; however, vinyl-type awnings may be allowed on more contemporary buildings, except as stated elsewhere relative to each district's guidelines. 6. Illumination of awnings is allowed; however, the illumination must be directed or focused toward the ground, not upward creating the effect of an oversized illuminated sign. Lighting external to the awning is also allowed. R. Canopies. Canopies can be constructed of canvas, well-crafted wood, or metal and are generally supported by vertical supports along their length. For the purposes of this sign code, however, a canopy that is of differing construction and that projects out from a building and/or is supported from above also falls under the guidelines outlined in this section. 1. Canopies are integral parts of buildings, and as such, require great sensitivity in order to make certain that they complement the design and character of the building. 2. Lettering on canvas or other fabric-type canopies should not be greater than six inches in height and should be located only on vertical surfaces and not on sloped or curved sections of the canopy. The front piece of a canopy may present an opportunity to prominently display a graphic symbol or logo with lettering no greater than six inches in height. Illumination of fabric-type canopies is allowed from the exterior or from within only if it is directed downward to the ground. 3. Larger identification or signage on canopies made of wood, metal or other permanent material may be allowed if it is compatible with the design of the canopy. Such signs may be internally illuminated, but in such cases, the background color must be darker than the color of the graphics. S. Temporary signs. Temporary signs may be installed for a predetermined length of time and must be removed at the end of that time period. The predetermined length of time must be approved by the design review board. Temporary signs may be wall signs, window signs, or banners, but in no case should a temporary sign obscure any architectural detail of a building. Temporary signs shall be installed in an unobtrusive manner so that their removal does not damage a building facade. 1. For sale and for lease signs do not require approval of the design review board if they are limited to one sign for each available space or building frontage and are five square feet or smaller. 2. Tethered signs such as blimps or balloons must be reviewed by the DRB for appropriateness and compatibility with surrounding establishments. Tethered signage must not drift into space above public rights-of-way or across surrounding property lines. T. Sandwich boards. One sandwich board sidewalk sign is allowed for each building and can identify multiple tenants on one sign. All such signs shall be designed to be folding in nature and must be removed at the close of business each day. The size of each face of a sandwich board shall not exceed 12 square feet and the overall sign shall be no taller than four feet. A sandwich board within the public right-of-way must be such that at least a five-foot unobstructed sidewalk width remains between the curb and the building front. U. Banners. Banners on streetlights are allowed throughout the CBID. Banners attached to buildings are allowed only within the downtown core. Standards for building banners are included within the individual district sections of this sign code. 1. Street banners are permitted only for nonprofit organizations or governmental entities. No for-profit, commercial enterprises will be allowed to hang banners to advertise or to promote their businesses, merchandise, products or services. 2. Banners should generally be event-oriented. For events lasting one week or longer, banners may be installed 30 days prior to the event. All banners must be removed within 14 days of the conclusion of the event. If banners are not removed within the required time frame, and if city crews perform removal, the organization will be assessed the cost and may be denied future banner requests. 3. The name of a for-profit sponsor organization or event may appear at the bottom of a banner in letters no more than one inch high and occupying no more than ten percent of the overall area of the banner. Logos may be permitted within that area. 4. Banners shall be a maximum of five feet in length and 30 inches wide. The minimum distance from the bottom of the banner to the top of the curb shall be 12 feet, unless it is installed on an existing mechanism that is currently part of the public infrastructure. 5. Coordination with the city engineer is necessary before any banner is installed on a street light. 6. Installation and removal of banners is the responsibility of the sponsoring organization, but must be performed by a licensed sign company with proof of adequate liability insurance. 7. Maintenance and replacement of damaged or missing banners is the responsibility of the sponsoring organization for the duration of the banners' display and shall be addressed in a timely manner. V. Illumination. Internally illuminated signs in which the background color is darker than the color of the graphics is encouraged. Exterior illumination, such as floodlights or spotlights, shall be positioned so that none of the light shines onto an adjoining property or in the eyes of motorists or pedestrians. For the purposes of these guidelines, neon-type lighting is considered external illumination. 1. Signs with marquee or bare bulb illumination shall not be located within 60 feet of any other similar sign or within 500 feet of any single, two-, three-, or four-family detached residential building. Exposed fluorescent tubes are not permitted. 2. There are no limits on neon tube illumination as a part of a sign and such lighting is strongly encouraged. Decorative neon accents intended to illuminate a building should be utilized only on nonhistoric structures and should not obscure any architectural details. 3. Signs are not required to be lit but in the event illumination is added, it must conform to this sign code. W. Mechanization. Mechanized signs that incorporate moving elements shall not be located within 60 feet of another similar sign or within 500 feet of any single-, two-, three-, or four-family detached residential building. X. Vehicles. Any sign painted or adhered to a vehicle that remains parked in front of any business establishment for the purposes of permanent advertising in the CBID is subject to review by the design review board. Such identification must meet the standards for identification and graphic elements explained above.
(Code 1985, § 7-53(d)(1); Ord. No. 4750, § 1, 3-7-2000)
Ask a question about Memphis law
Corpus searches the Memphis sections it holds and shows the ones that match, with their citations. Free, no sign-in.
