§ 27-289.3 — Allowable signs
Code of Ordinances, City of Tampa (Supp. No. 148: codified through Ordinance No. 2025-152, enacted December 18, 2025) · Tampa City Code § 27-289.3
Corpus is an independent public-information project, not the official City of Tampa website. Stable reference: corpuslaw.us/code/64ee13b5-c5bb-4375-a69b-917f9615bc0f
Sec. 27-289.3. - Allowable signs.
(a) The following signs are exempt from permit requirements of this Sign Code, unless otherwise stated herein or required pursuant to other provisions of the City of Tampa Code of Ordinances: (1) Government signs. No permit is required if a government sign is necessary for the purposes of public health and safety, or is used to identify public services or public facilities, for traffic control, for events, for wayfinding or directions, or to provide information to the community. Otherwise a government sign must comply with requirements of this chapter. Any government sign which contains an electronic message must operate in compliance with subsection 27-289.6(b). (2) Flags when displayed on a single pole or other supporting structure, subject to the following restrictions: Zoning district | Maximum height | Maximum size | Number of flags | Location of flags Residential | 35 feet | 50 square feet | Any number, up to a maximum of 50 square feet per lot | 0 foot setback, subject to the provisions of section 27-283.5 Non-Residential | 45 feet | 50 square feet | Any number, up to a maximum of 50 square feet per lot | 0 foot setback, subject to the provisions of section 27-283.5 (3) Signs cut into masonry surfaces without paint or other effect. Such signs might include memorial signs or tablets, names of buildings, and dates of erection. (4) Two (2) signs per driveway located in non-Residential districts, or at the entrance to a residential subdivision, multi-family development, or mobile home park, provided that: a. The signs are located on private property and pertain to directing traffic, emergency responders, or pedestrians safely on or off of such property; b. Each sign shall not exceed four (4) square feet in sign area nor thirty (30) inches in height; c. If illuminated, an electrical permit shall be obtained in accordance with chapter 5, City of Tampa Code; d. Signs may be placed with a zero (0) foot setback from the right-of-way, subject to the provisions of section 27-283.5. The square footage of signs under this subsection (4) shall not be counted as part of the maximum allowable square footage for any parcel. (5) Temporary signs, subject to the following restrictions: a. Each zoning lot of record shall be allowed the following temporary signs without permit, provided that each temporary sign complies with subsection (a)(5)(ii) below: 1. One temporary sign per 200 feet of frontage or portion thereof; and 2. Warning signs; and 3. Any number of signs, which are associated with an event, including but not limited to: i. During the time a property is actively marketed for sale, rent, or lease on such sign or in one or more paper or online listing(s); ii. During the time the property is under construction, provided that such signs are removed prior to issuance of a certificate of occupancy; iii. For a local, state, or national election; iv. Holiday, seasonal, or commemorative decorations; or v. For a public or semipublic event or function. b. All temporary signs placed under this subsection (5) shall not be considered as part of the maximum square footage permitted on any parcel, and are subject to the following restrictions: 1. No illumination is permitted, nor may any part of the sign be electronic. 2. Event signs shall be erected no more than sixty (60) consecutive calendar days prior to the event and shall be removed within six (6) consecutive calendar days of the conclusion of the event. 3. A maximum of thirty-two (32) square feet of total temporary signage is permitted at any one time per parcel. 4. No single temporary sign may exceed the following sizes: Zoning district | Maximum sign surface area | Maximum height (ft) Residential | 8 SF | 6 ft Non-Residential Property has less than 200 feet of street frontage | 8 SF | 10 ft Property has 200 or more feet of street frontage | 16 SF | 10 ft (6) Window signs which comprise, in aggregate, twenty-five (25) percent of the total window area or less. (7) Signs incorporated on machinery or equipment at the manufacturer's or distributor's level, such as signs customarily affixed to vending machines, newspaper racks, and gasoline pumps. Such signs shall not be counted as part of the maximum square footage permitted on any parcel. (8) Interior signs which are displayed on the inside of a building and not visible from a public place. Such signs shall not be counted as part of the maximum square footage permitted on any parcel. (9) One (1) address sign of no more than two (2) square feet of total sign face area in Residential districts and no more than three (3) square feet of total sign face area in Non-Residential districts. The square footage for the address sign shall be allowed in addition to the total sign surface area allowed for freestanding and/or building signs. (10) Signage applied to outdoor furniture, including umbrellas, that shall consist of no more than one (1) line of letters or an identification emblem, initials or insignia, or other feature painted on the furniture. (11) Signs which are required pursuant to the City of Tampa Code of Ordinances, Florida Statutes or other regulations in the location and up to the size required by the applicable regulation shall be allowed. Such legally required signage shall be allowed in addition to the total sign surface areas allowed for other signage provided for in this Sign Code. (b) The following signs are allowed only with a permit: (1) In addition to the temporary signage allowed under subsection (a)(5) above, one (1) temporary sign exceeding the size of a sign allowed under section (a)(5) may be displayed for a period not to exceed thirty (30) consecutive calendar days, nor more than sixty (60) days in a single year (up to ninety (90) days in the Central Business District as defined in Chapter 27, City of Tampa Code of Ordinances), provided: a. No such temporary sign may be displayed at a height of more than fifteen (15) feet (except in the Central Business District as defined in Chapter 27, City of Tampa Code of Ordinances, a temporary sign attached to a building may not exceed the height of the building upon which the sign is attached), nor shall such sign be any larger than a building sign allowed for the parcel on which the sign is displayed; b. The temporary sign shall be displayed only in non-residential zoning districts, or within non-residential or mixed use designated areas of site plan districts; c. The temporary sign shall be attached to the building in a manner as provided for in Chapter 5 of the City Code and shall not be affixed to vehicles or utility poles except as provided for in Chapter 22 of the City Code; d. The temporary sign shall be maintained in a state of good repair, and such signs that are frayed, torn, or otherwise in disrepair are prohibited. A permit is required prior to the installation of any temporary sign exceeding the size of a temporary sign allowed under section (a)(5) above. (2) At each entrance to a platted subdivision, one (1) double-faced or two (2) single-faced permanent sign(s), provided that all of the following requirements are met: a. The sign(s) shall not create a physical or visual hazard for pedestrians, bicyclists, or motorists entering or leaving the subdivision and shall be set back a minimum of fifteen (15) feet from the right-of-way line and thirty (30) feet from the intersection of the rights-of-way; b. An individual, firm, partnership, association, corporation or other legal entity shall be designated as the person responsible for the perpetual maintenance for the subdivision sign(s); c. The sign(s) shall not exceed ten (10) feet in height; and d. The sign(s) shall not exceed a total of forty (40) square feet in aggregated display area. (3) At each entrance to a multiple family residential development or mobile home park, one (1) double-faced or two (2) single-faced permanent building or freestanding sign(s) may be located, provided that all of the following requirements are met: a. The sign(s) shall not create a physical or visual hazard for pedestrians, bicyclists, or motorists entering or leaving the development and shall be set back a minimum of fifteen (15) feet from the right-of-way line and thirty (30) feet from the intersection of the rights-of-way; b. Within the CBD, refer to art. III, div. 2., subdn. 3; c. Such signs shall not exceed two (2) square feet in display area for each dwelling unit, up to and including twenty (20) units—in no event shall the sign(s) exceed forty (40) square feet of aggregated display area; d. Such signs shall not exceed ten (10) feet in height; and e. Such signs shall be set back fifteen (15) feet from the right-of-way line and thirty (30) feet from the intersection of the rights-of-way. (4) Two (2) signs per driveway located in Non-Residential districts or at the entrance to a residential subdivision, multi-family development, or mobile home park, provided that all of the following requirements are met: a. The signs pertain to directing traffic, emergency responders, or pedestrians safely on or off of such property; b. The entire sign structure shall not exceed five (5) feet in height; c. The sign copy shall not exceed twelve (12) inches or thirty-two (32) square feet; and d. Such signs shall meet the separation and setback requirements of freestanding signs in subsection (b)(5) below. (5) Freestanding signs. Freestanding signs shall be allowed in office, commercial and industrial districts, provided the following specific regulations are met (refer to sec. 27-289.4 for electronic message sign standards): a. Number: One (1) Freestanding sign is permitted for each parcel having street frontage. Additional signs are allowed as follows: 1. For a corner lot, as defined in section 27-161, one (1) additional freestanding sign is permitted to be located adjacent to the second street frontage provided that the second street frontage is a minimum of three hundred (300) feet of continuous, lineal public street frontage; or 2. For a parcel with a street frontage greater than three hundred (300) feet, one (1) additional freestanding sign is permitted for each additional three hundred (300) feet of continuous, lineal street frontage. b. Placement (See Diagram 2): 1. The placement and orientation of a freestanding sign shall be limited to arterial and/or collector street roadways (as identified in the City of Tampa Department of Public Works "Roadway Functional Classification System"), unless either of the following situations exist: i. The zoning lot has street frontage only on local street; or ii. The zoning lot has street frontage on a local street where the entire block face on both sides of the local street has no residentially zoned or used parcels. 2. Freestanding signs shall be placed no closer than one hundred fifty (150) feet apart on the same zoning lot. 3. Freestanding signs shall be placed no closer than ten (10) feet from any residential zoning district. For the purpose of determining the spacing requirement found in this subsection, distances shall be measured from the sign structure to the property line of the nearest residentially zoned property. c. Size: 1. The allowable sign area for a freestanding sign shall be one (1) square foot of sign surface area for each lineal foot of street frontage on an abutting public street as follows: Feet of Frontage | Maximum Sign Surface Area (SF) < 20 feet | 20 (SF) per sign face 20 feet to 50 feet | 20—50 SF per sign face (1 SF per foot of street frontage) > 50 feet | 50 SF per sign face 2. If a parcel is entitled to more than one (1) freestanding sign under this section, then two (2) or more allowable freestanding signs may be combined into a single freestanding sign, not to exceed a maximum allowable sign surface area of one hundred (100) square feet per sign face. 3. The allowable sign surface area shall not include any decorative elements surrounding the sign face. However the decorative elements shall not protrude more than three (3) feet beyond the sign face. d. Height-Setback: The maximum height of a freestanding sign at the five-foot setback line shall be ten (10) feet, measured from the established grade at the property line along the right-of-way from the closest leading edge of the freestanding sign. For every one (1) foot of additional setback, the height of the freestanding sign may be increased by one (1) foot to a maximum height of twenty (20) feet. In no event may the freestanding sign interfere with the visibility triangle as provided in section 27-283.5 of the City Code. e. Design: The sign face shall be supported by a sign structure which shall consist of a single pier or pillar with a minimum diameter or horizontal dimension of thirty (30) inches or, alternatively, by two (2) piers or pillars, each with a minimum diameter or horizontal dimension of twelve (12) inches. The sign structure shall have materials and architectural details consistent with the principal building it serves or in a manner shown in Diagrams 3 and 4 below. Diagram 1 [image omitted; see the official code] Diagram 2 [image omitted; see the official code] Diagram 3 [image omitted; see the official code] Diagram 4 [image omitted; see the official code] (6) Building signs. Building signs shall be allowed in office, commercial and industrial districts, provided the following specific regulations are met (refer to section 27-289.4 for electronic message sign standards): a. Number: 1. Single occupancy parcels. i. One (1) building sign shall be permitted for each single-occupancy parcel having street frontage. Corner parcels or double-frontage parcels shall be allowed one (1) sign per street frontage. ii. One (1) marquee sign or projecting sign, as set forth in subsections (b)(7) below, may be substituted for each permitted building sign. iii. Canopy and awning signs may be substituted for, or permitted in addition to, building signs, subject to the maximum sign surface area set forth in subsection (b)(6)b. below. 2. Multi-occupancy parcels. i. One (1) building sign shall be permitted for each establishment with a main door entrance which faces a public street in a multiple-occupancy parcel. Establishments located at a corner shall be allowed one (1) building sign for each side of the establishment which faces a public street. ii. One (1) marquee sign or projecting sign, as set forth in subsections (b)(7) below, may be substituted for each permitted building sign, subject to subsection (b)(6)a.2.iv. below. iii. Canopy and awning signs may be substituted for, or permitted in addition to, building signs, subject to the maximum sign surface area set forth in subsection (b)(6)b. below. iv. Building signs displayed on a multi-occupancy parcel shall be uniformly designed, subject to subsection (b)(6)a.2.iv. below. b. Size: 1. The maximum allowable sign surface area for each building sign shall be one and one-quarter (1¼) square feet per linear foot of building frontage abutting public street, excluding parking garages that abut a public street, unless otherwise specified in article III, division 2, special districts or artticle IV, overlay districts. 2. The maximum allowable display area for awning, canopy, and marquee signs shall not exceed two (2) square feet per linear foot of building frontage facing a public street. c. Design: 1. One (1) projecting sign may be substituted for each building sign, as provided in subsection (b)(7) below. Marquee, canopy, or awning signs may be substituted for, or permitted in addition to, building signs. 2. Building signs shall not project beyond the roofline or side walls of the establishment to which the sign is attached, nor shall the building sign project more than twelve (12) inches out from the wall to which it is attached. 3. Building signs may contain a six-inch decorative border which shall not be counted as part of the sign surface area calculations. (7) Projecting signs. Projecting signs shall be allowed in office, commercial and industrial districts, provided the following specific regulations are met: a. Projecting signs shall not project more than four (4) feet from the building wall to which the projecting sign is attached. b. Projecting signs shall not be located above the roofline of the building. c. The supporting hardware, unless incorporated as a decorative component of a projecting sign shall not be visible from the street or sidewalk. d. Projecting signs shall not be constructed in violation of the public space encroachment limitations specified in this chapter or other applicable city code. e. Projecting signs shall not be erected closer than ten (10) feet from another projecting or marquee sign, or a residential property line. f. Projecting signs, when specifically allowed by this Code, which project over any public or private pedestrian way shall be elevated a minimum of ten (10) feet above such pedestrian way. Projecting signs, when specifically allowed by this Code, which project over any public or private street shall be elevated a minimum of sixteen (16) feet above such street.
(Ord. No. 2017-103, § 8(Exh. A), 6-22-2017; Ord. No. 2018-92, § 2, 6-28-2018; Ord. No. 2018-151, § 1, 10-4-2018)
Ask a question about Tampa law
Corpus searches the Tampa sections it holds and shows the ones that match, with their citations. Free, no sign-in.
