Sec. 14-186. - Locking devices.
(a) Generally. All exterior openings of any building used for business purposes and subject to the provisions of this article and not otherwise protected by photoelectric, ultrasonic or other intrusion detection devices, approved by the chief of police, shall be secured as provided in this section.
(b) Front doors. All front doors of any such building or premises shall comply with the following requirements:
(1) Tempered glass doors, wood or metal doors with tempered glass panel, solid wood or metal doors shall be secured as follows:
a. A single door shall be equipped with either double-cylinder dead lock that unlocks from both the outside and inside by key, or with cylinder dead lock that unlocks from the outside by key and inside by turnpiece, handle or knob, or with dead locking latch having guarded bolt that unlocks from the outside by key and inside by turnpiece, handle or knob, or with dead locking latch having guarded bolt that unlocks from the outside by key and inside by turnpiece, handle or knob.
b. On double doors the active leaf shall be equipped with a type of lock as prescribed for single doors, and the inactive leaf shall be equipped with flush bolts at head and foot.
(2) Doors with glass panels not of tempered glass and doors that have nontempered glass panels adjacent to the door frame shall be secured as follows:
a. A single door shall be equipped with cylinder dead lock that unlocks from both the outside and inside by a key.
b. On double doors the active leaf shall be equipped with a cylinder dead lock that unlocks from both the outside and inside by a key, and the inactive leaf shall be equipped with flush bolts at head and foot.
(3) Rolling overhead doors that are not controlled or locked by electric power operation shall be equipped on the inside with the following protective devices:
a. Manually operated doors shall be provided with slide bolts on the bottom bar.
b. Chain-operated doors shall be provided with a cast iron keeper and pin for securing the hand chain.
c. Crank-operated doors shall be provided with a means for securing the operating shaft.
(4) A solid overhead, swinging, sliding or accordion garage-type door shall be secured with a cylinder lock, padlock and/or metal slide bar, bolt or crossbar on the inside when not otherwise controlled or locked by electric power operation. If a padlock is used, it shall be of hardened steel shackle, with minimum four-pin tumbler operation. If this type of door provides the only entrance to the front of the building, a cylinder lock or padlock may be used on the outside.
(5) Metal accordion grate or grill type doors shall be equipped with a metal guide track at top and bottom and a cylinder lock and/or padlock with hardened steel shackle and minimum four-pin tumbler operation.
(6) Outside hinges on all front doors shall be provided with nonremovable pins. Such hinge pins may be either welded, flanged or secured by a screw.
(c) Rear, side and basement doors. All accessible rear, side and basement doors of any such building or premises shall comply with the following requirements:
(1) All doors of the types listed below shall comply with the requirements of subsection (b) of this section for front doors:
a. Tempered glass doors, wood or metal doors with tempered glass panel.
b. Metal doors.
c. Rolling overhead doors.
d. Solid overhead, swinging, sliding or accordion garage type doors.
e. Metal accordion grate or grill type doors.
(2) Doors with glass panels and doors that have glass panels adjacent to the door frame shall be secured as follows:
a. The glass panel shall be covered with iron bars of at least one-half-inch round or one-inch by one-fourth-inch flat steel material spaced not more than five inches apart.
b. Iron or steel grills of at least one-eighth-inch material of two-inch mesh.
c. If the door or glass panel barrier is on the outside it shall be secured with rounded head flush bolt on the outside.
d. If the remaining portion of a door panel exceeds eight inches by 12 inches (excluding door frame), is of wood but not of solid core construction or is less than 1⅜ inches thick, such portion shall be covered on the inside with at least 16 gauge sheet steel attached with screws.
(3) Wood doors not of solid core construction or with panels less than 1⅜ inches thick shall be covered on the inside with at least 16 gauge sheet steel attached with screws.
(4) Locking devices are regulated as follows:
a. A single door shall be equipped with either double cylinder deadlock that unlocks from both the outside and inside by key or with cylinder deadlock that unlocks from the outside by key and inside by turnpiece, handle or knob with dead locking latch having guarded bolt that unlocks from outside by key and inside by turnpiece, handle or knob or with approved slide bar bolt, crossbar, and/or padlock. If a padlock is used, it shall be of hardened steel shackle with minimum four-pin tumbler operation.
b. On double doors, the active leaf shall be equipped with a type of lock as prescribed for single doors above and the inactive leaf shall be equipped with flush bolts at head and foot.
(5) Outside hinges on all rear, side and basement doors shall be provided with nonremovable pins. Such hinge pins may be either welded, flanged or secured by a screw.
(d) Roof doors. All doors that exit onto the roof of any such building or premises shall comply with the following requirements:
(1) Doors with glass panels and any glass panels that are adjacent to the door frame shall be protected as follows:
a. The glass portion shall be covered with iron or steel grills of at least one-eighth-inch material of no more than two-inch mesh securely fastened.
b. If the door or glass panel barrier is on the outside, it shall be secured with rounded head flush bolt on the outside.
c. If the remaining portion of a door panel exceeds eight inches by 12 inches (excluding door frame) and is of wood but not of solid core construction or is less than 1⅜ inches thick, such portion shall be covered on the inside with at least 16 gauge sheet steel attached with screws.
(2) Wood doors not of solid core construction or with panels less than 1⅜ inches thick shall be covered on the inside with at least 16 gauge sheet steel attached with screws.
(3) All roof doors shall be provided with a lock that will permit the door to be opened from the inside without the use of a key or any special knowledge or effort.
(4) Outside hinges on all roof doors shall be provided with nonremovable pins. Such hinge pins may be either welded, flanged or secured by a screw.
(e) Glass windows. The chief of police shall, with the advice and assistance of the fire chief, determine the extent of protection, if any, that will be required for accessible glass windows at the side or rear of such building. Glass windows shall be deemed accessible if less than 18 feet aboveground. In making his determination, he shall consider whether the side of the building fronts on a street, the area, the location and its contents, and whether such openings are protected by intrusion detection devices.
(1) The chief of police may require side and rear glass windows with a pane exceeding 96 square inches in area with its smallest dimension exceeding six inches to be protected in the following manner:
a. Inside or outside iron bars of at least one-half inch round or one-inch by one-fourth-inch flat steel material spaced not more than five inches apart, securely fastened; or
b. Inside or outside iron or steel grills of at least one-eighth-inch material of two-inch mesh securely fastened. If such barrier is on the outside, it shall be secured with rounded head flush bolt on the outside.
(2) If the side or rear window is of the type that can be opened, it shall, where applicable, be secured on the inside with either a glide bar, bolt, crossbar and/or padlock with hardened steel shackle, and minimum four-pin tumbler operation.
(3) Outside hinges on all side and rear glass windows shall be provided with nonremovable pins. Such hinge pins may be either welded, flanged or secured by a screw.
(f) Accessible transoms. All exterior transoms exceeding eight inches by 12 inches on the side and rear of any such building or premises shall be protected by either of the following:
(1) Outside iron bars of at least one-half-inch round or one-inch by one-fourth-inch flat steel material spaced no more than five inches apart; or
(2) Outside iron or steel grills of at least one-eighth-inch material but not more than two-inch mesh. Such barrier shall be secured with rounded head flush bolts on the outside.
(g) Roof openings. All exterior openings on the roof of any building or premises shall be protected as follows:
(1) Glass skylights shall be provided with:
a. Iron bars of at least one-half-inch round or one-inch by one-fourth-inch flat steel material under the skylight and securely fastened; or
b. A steel grill of at least one-eighth-inch material of two-inch mesh under the skylight and securely fastened.
(2) Hatchway openings shall be secured as follows:
a. If the hatchway is of wooden material, it shall be covered on the inside with at least 16 gauge sheet steel attached with screws.
b. The hatchway shall be secured from the inside with a slide bar or slide bolts. The use of crossbar or padlock is unauthorized unless approved by the fire chief.
c. Outside hinges on all hatchway openings shall be provided with nonremovable pins. Such hinge pins may be either welded, flanged or secured by a screw.
(3) Air duct or air vent openings exceeding eight inches by 12 inches shall be secured by covering the same with either of the following:
a. Iron bars of at least one-half-inch round or one-inch by one-fourth-inch flat steel material spaced no more than five inches apart and securely fastened; or
b. A steel grill of at least one-eighth-inch material of two-inch mesh and securely fastened. If the barrier is on the outside, it shall be secured with rounded head flush bolts on the outside.
(Code 1975, § 24-5)