TV and radio broadcasting antennae.
El Paso City Code § 20.10.700
in effect20.10.700 - TV and radio broadcasting antennae.
A. In Residential, Apartment and Commercial Zoning Districts. Ground-mounted radio or television broadcasting antenna support structures with antennas and equipment storage facilities shall comply with the following standards:
1. The antenna support base shall be set back one foot for each one foot of height from abutting residential districts, measured from the antenna support base to the property line;
2. The radio or television broadcasting antenna support structure shall conform with FCC and FAA height regulations within a residential zone;
3. The following must accompany a request for a special permit:
a. A nonionizing electromagnetic radiation (NIER) report, in a format acceptable to the FCC,
b. A structural engineering report for the antenna support,
c. A detailed site development plan showing the antenna, supporting structures and appurtenant equipment in relation to the existing surroundings,
d. Verification letters that an FCC application has been submitted and FAA approval has been obtained;
4. Collocation or installation of additional antennas on an existing antenna support structure shall be permitted after review and approval by the building official of a structural recertification report, prepared and sealed by a licensed professional engineer, and an updated NIER emissions report;
5. Increase in elevation of an existing antenna support structure shall be permitted, so long as the setback and maximum height limitations are complied with, after review and approval by the building official of updated structural and NIER emissions reports;
6. Existing nonconforming antenna support structures, unable to comply with current setback limitations shall be prohibited from any increase in elevation.
B. In manufacturing and Industrial Zoning Districts. Ground-mounted radio or television broadcasting antenna support structures, with appurtenant antennas and equipment storage facilities shall comply with the following standards:
1. The antenna support base shall be set back from any residential district or residential use one foot for each one foot of height, measured from the antenna support base to the property line. The maximum height limits shall be set by the Federal Communication Commission (FCC) and Federal Aviation Administration (FAA) license requirements;
2. The following must accompany a request for a building permit:
a. A detailed plan showing the antenna, support structures, and appurtenant equipment in relation to the existing surroundings including fencing, off-street parking, and access from the antenna support to the nearest public access,
b. A nonionizing electromagnetic radiation (NIER) report, in a format acceptable to the FCC,
c. A structural engineering report for the antenna support,
d. Verification letters that an FCC application has been submitted and FAA approval has been obtained;
3. Collocation or installation of additional antennas on an existing antenna support structure shall be permitted after review and approval by the building official of a structural recertification report prepared and sealed by a licensed, professional engineer;
4. Increase in elevation of an existing antenna support structure shall be permitted, only when the setback limitations are complied with, after review and approval by the building official of updated structural and NIER emissions reports. Existing nonconforming antenna support structures, unable to comply with current setback limitations shall be prohibited from any increase in elevation.
5. The applicant shall provide a six-foot high fence or screening wall around the wall around the base of a self-supporting or guyed mast antenna support, and appurtenant equipment storage facilities, to provide for security. The gate providing access to the antenna support shall remain locked at all times, except when being used for access by maintenance personnel;
6. The access driveway and one off-street parking space, for use by maintenance vehicles, must be paved covered with an alternative all-weather material to provide for a dust-free driving surface as approved by the director of the city development department or other designee of the city manager.
(Ord. 16653 § 2 (part), 2007) (Ord. No. 17442, § 29, 10-26-2010; Ord. No. 17801, § 6, 6-5-2012, eff. 6-11-2012)
Source: City of El Paso, City Code and City Charter (Municode Library, library.municode.com)URL: https://library.municode.com/tx/el_paso/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.10SUUSRE_20.10.700TVRABRANFetched: 10/28/2026
