Parking area design.
Tulsa Revised Ordinances tit. 42, § 55.090
in effectSection 55.090. - Parking area design.
A. Applicability. The parking area design regulations of this section apply to all off-street parking lots for motor vehicles, whether containing required parking spaces or non-required parking spaces.
B. Ingress and egress. All parking areas must be designed to allow vehicles to enter and exit a street and cross public sidewalks in a forward motion, except that this requirement does not apply to lots with access on a minor street.
C. Stall size. Parking spaces must be at least eight and one-half (8.5) feet in width and eighteen (18) feet in length, exclusive of access drives and aisles. In parking areas where permanent wheel stops have been installed, two and one-half (2.5) feet of the parking space length (depth) beyond the wheel stop may be counted as part of the required stall length if that area is unobstructed and not part of another parking stall, drive aisle or sidewalk.
D. Parking area layout (geometrics). Parking areas must be designed and marked in accordance with the dimensional standards of Table 55-5, which shows minimum dimensions for various parking layouts (angles). Requirements for layouts or angles not shown in Table 55-5 may be interpolated from the layouts shown, as approved by the development administrator.
Table 55-5: Parking Area Geometrics
Stall Angle | Stall Width | Stall Length | Aisle Width (1-way/2-way)
0° | 8.5 | 22.0 | 12.0/20.0
9.0 | 22.0 | 12.0/20.0
45° | 8.5 | 18.0 | 12.0/20.0
9.0 | 18.0 | 11.0/19.0
60° | 8.5 | 18.0 | 16.0/21.0
9.0 | 18.0 | 15.0/20.0
75° | 8.5 | 18.0 | 21.0/22.0
9.0 | 18.0 | 20.0/21.0
90° | 8.5 | 18.0 | -/24.0
9.0 | 18.0 | -/22.0
10.0 | 18.0 | -/20.0
Figure 55-5: Parking Area Geometrics
[image omitted; see the official code]
E. Tandem parking. Tandem parking spaces may be used to satisfy parking requirements for household living uses when the spaces are assigned to the same dwelling unit. In all other cases parking spaces must be designed to allow each parking space to be accessed without passing through another parking space. Tandem parking arrangements must have a minimum stall of eight and one-half (8.5) feet and a minimum length of thirty-six (36) feet.
Figure 55-6: Tandem Parking
[image omitted; see the official code]
F. Surfacing.
1. All off-street parking areas must be surfaced with a dustless, all-weather surface unless otherwise expressly stated in this zoning code. Pervious pavement or pervious pavement systems are allowed subject to the supplemental regulations of Section 55.090F.6. Parking area surfacing must be completed prior to initiation of the use to be served by the parking.
2. All motorized vehicles designed for travel upon public streets and all recreational vehicles that are being parked, stored or displayed for sale must be parked, stored or displayed on a dustless, all-weather surface. This surfacing requirement does not apply to junk or salvage yards. The board of adjustment is authorized to grant a special exception permitting the parking, storage or display of motorized vehicles or recreational vehicles on a surface other than one consisting of a dustless, all-weather surface if the location complies with all applicable minimum building setbacks.
3. Driveways, not including parking spaces, that serve residential uses in AG and AG-R zoning districts may be surfaced with gravel in place of a dustless, all-weather surface outside of the street right-of-way.
4. As an alternative to fully paved driveways, ribbon driveways serving residential dwelling units are allowed, subject to the following provisions:
a. Ribbon driveways consist of at least two wheel strips, at least two (2) feet in width each, constructed with concrete.
b. The wheel strips must be separated by a permeable surface with a maximum width of four (4) feet. The space between the wheel strips may be planted with turf, grass, or other ground cover, or filled with landscaping rocks or gravel. Gravel or rocks that have migrated onto adjacent areas must be regularly swept and removed. The permeable space between wheel strips does not count toward satisfying minimum open space per unit requirements.
c. The overall width of the driveway is measured from the outer edges of the outside wheel strips and includes the aggregate widths of all wheel and permeable strips.
d. Within the right-of-way, driveways must be fully paved across their total width. (Refer to the City of Tulsa Standard Specifications and Details for Residential Driveways #701—704.)
5. In RE, RS, RD, and RT zoning districts, driveways serving residential dwelling units may not exceed 50% of the lot frontage or the following maximum widths, whichever is less, unless a greater width is approved in accordance with the special exception procedures of Section 70.120, or, if in a PUD, in accordance with the amendment procedures of Section 30.010I.2. (Refer to the City of Tulsa Standard Specifications and Details for Residential Driveways #701—704.)
Table 55-6: Maximum Driveway Widths in RE, RS, RD, and RT Zoning Districts
Maximum Driveway Width
Street Frontage | 75'+ | 60'—74' | 46'—59' | 30'—45' | Less than 30' [2]
Driveway Within Right-of-Way (feet) [1] | 27' | 26' | 22' | 20' | 12'
Driveway Within Street Setback (feet) [1] | 30' | 30' | — | — | —
[1] Maximum width is the sum of the width of all driveways.
[2] Provided that for street frontages less than twenty-four (24) feet, a driveway up to twelve (12) feet in width is permitted.
For approvals granted under the terms of the zoning code in effect prior to January 1, 2016, including: (1) variances of maximum driveway coverage measured by width, square footage or percentage of yard; and (2) establishment of PUD development standards that increase the maximum permitted driveway coverage measured by any such means, the foregoing maximums do not apply.
6. Pervious pavement or pervious pavement systems, including pervious asphalt, pervious concrete, modular pavers designed to funnel water between blocks, lattice or honeycomb shaped concrete grids with turf grass or gravel filled voids to funnel water, plastic geocells with turf grass or gravel, reinforced turf grass or gravel with overlaid or embedded meshes, resin-bound pervious pavement systems, or similar structured and durable systems are allowed as parking lot surfacing materials. Gravel, turf, or other materials that are not part of a structured system designed to manage stormwater are not considered pervious pavement or a pervious pavement system. Pervious pavement and pervious pavement systems must comply with the following:
a. Materials must be installed and maintained in accordance with all applicable city standards. Damaged areas must be promptly repaired. Gravel that has migrated from a pervious pavement system onto adjacent areas must be regularly swept and removed.
b. Accessible parking spaces and accessible routes from the accessible space to the principal structure or use served must comply with the building code.
c. Pervious pavement or pervious pavement systems are prohibited in areas used for the dispensing of gasoline or other liquid engine fuels or where other hazardous materials are used or stored.
d. Parking areas with pervious pavement or pervious pavement systems must have the parking spaces marked as required by this chapter, except that pervious pavement systems that utilize gravel or turf may use alternative marking to indicate the location of the parking space, including markings at the end of spaces on the drive aisle or curbing, wheel stops, or concrete or paver strips in lieu of painted lines.
G. Vertical clearance. All parking spaces must have overhead vertical clearance of at least seven (7) feet.
H. Landscaping and screening. See Chapter 65.
I. Lighting. See Chapter 67.
(Ord. No. 25330, § 14, 6-5-2024; Ord. No. 25656, § 21, 9-10-2025)
Source: City of Tulsa, Revised Ordinances and City Charter (Municode Library, library.municode.com)URL: https://library.municode.com/ok/tulsa/codes/code_of_ordinances?nodeId=COOR_TIT42ZOCO_CH55PA_S55.090PAARDEFetched: 10/28/2026
