Residential Limited.
Metropolitan Code of Nashville and Davidson County § 17.38.010.B
in effect17.38.010.B - Residential Limited.
[image omitted; see the official code]
[image omitted; see the official code]
1. Intent. Intended for residential development, generally in the form of houses, townhouses, or small apartment buildings, with private or shared open space. This district is appropriate for providing moderate levels of density at strategic locations close to transit corridors.
2. Zones.
Zones | Context
Residential Limited 1 (RL1) | Suburban
Residential Limited 2 (RL2) | Urban
Residential Limited 3 (RL3) | Center
3. Allowed Building Types.
Allowed Building Types | Eligible for Voluntary Attainable Housing Incentive
Single Family | No
Two Family | No
Townhouse | Yes
House Court | No
Townhouse Court | Yes
Plex House | Yes
Manor House | Yes
Multiplex | Yes
Low-rise Courtyard Flats | Yes
Low-rise Flats (RL3 only) | Yes
Note 1: Detached Accessory Dwelling Units allowed with Single Family Building Types with conditions from Section 17.16.30.G, except for lot area, height, and setbacks, which are regulated by this chapter.
Note 2: Not-owner occupied Short Term Rentals are prohibited. Owner-occupied Short Term Rentals allowed with Single Family Building Type only per Section 6.28.30.
Note 3: Non-residential uses are permitted per Table 17.08.030 and are subject the bulk standards for R6 in Table 17.12.020B.
4. Lot.
Lot Size | RL1 | RL2 | RL3
Area | 5,000 sf min. | 5,000 sf min. | 5,000 sf min.
Width | [image omitted; see the official code] | 50' min. | 40' min. | 40' min.
Depth | [image omitted; see the official code] | 90' min. | 90' min. | 90' min.
Minimum lot area, lot width, and lot depth requirements shall be waived if in compliance with Section 17.40.670 and one of the following conditions are met: • The site has access to a side street or improved alley. • The width of the primary structure's main body is at least 18 feet wide, and the highest roofline of the primary structure does not exceed a ratio of 1.0 horizontal to 1.5 vertical.
5. Building Placement.
Setback | RL1 | RL2 | RL3
Front (Build-To Zone) | [image omitted; see the official code] | 10' min.; 25' max. | 10' min.; 25' max. | 5' min.; 15' max.
Side Street (Build-To Zone) | [image omitted; see the official code] | 10' min.; 25' max. | 10' min.; 20' max. | 5' min.; 15' max.
Side | [image omitted; see the official code] | 5' min. | 5' min. | 5' min.
Rear
Main Building | [image omitted; see the official code] | 10' min. | 10' min. | 10' min.
Accessory Structure(s) | [image omitted; see the official code] | 5' min. | 5' min. | 5' min.
Setbacks should align with the contextual setback (see Section 17.12.030.c(3). If the contextual setback is greater than the max setback for the district, then the district max shall apply.
Facade Zone
Main building shall define required % of the linear length of the Front Build-To Zone | 50% min.
Main building shall define required % of the linear length of the Side Street Build-To Zone | 30% min.
Encroachments into Setbacks
Private Frontage Types may encroach into front and side street setbacks; and shall not be located in side or rear setbacks.
Architectural features may encroach up to 5 feet into building setbacks. Architectural features cannot cross property lines.
Fences, freestanding landscape walls, shrubs and landscaping may encroach up to 3 feet into front or side street setbacks; and are allowed within side and rear setbacks.
Stormwater features may encroach into setbacks.
Encroachments are not allowed within utility easement area, ROW, alley, or across a property line.
Landscape Buffer
See Table 17.24.230 for landscape buffer yard requirements.
No landscape buffer yard is required between properties zoned RN and RL.
Figure: 17.38.010.B(1). For A, B, C, D, E, F, and G see lettered sections in 17.38.010.B Table 4 and Table 5 for minimum and maximum requirements.
[image omitted; see the official code]
6. Building Form.
Height | RL1 | RL2 | RL3
Main Building
Stories | 2.5 max. | 3 max. | 4 max.
See Section 17.38.020 for additional height standards. Building type standards may further limit height. Height shall be measured from the average grade plane post-development.
Highest Roof Line (H) | [image omitted; see the official code] | Maximums are set by building type.
Highest Eave (I) | [image omitted; see the official code]
Accessory Structure(s)
Stories | 2 max. | 2 max. | 2 max.
Highest Roof Line | 30' max. | 30' max. | 30' max.
Highest Eave | 24' max. | 24' max. | 24' max.
Floor-to-Floor | RL1 | RL2 | RL3
Ground Floor | [image omitted; see the official code] | 9' min. | 9' min. | 9' min.
Upper Floors | [image omitted; see the official code] | 8' min. | 8' min. | 8' min.
Ground Floor Residential or Active Space | RL1 | RL2 | RL3
Depth of active ground floor use along front and side street façade | [image omitted; see the official code] | 10' min. | 10' min. | 10' min.
Coverage | RL1 | RL2 | RL3
Building Coverage | 0.6 max. | 0.6 max. | 0.6 max.
See Section 17.28 for Environmental Performance Standards.
Figure: 17.38.010.B(2). For H, I, J, K, and L, see lettered sections in 17.38.010.B Table 6 for minimum and maximum requirements.
[image omitted; see the official code]
7. Parking Location.
Setback | RL1 | RL2 | RL3
Front | [image omitted; see the official code] | 10' behind facade | 10' behind facade | 10' behind facade
Side Street | [image omitted; see the official code] | 10' behind facade | 10' behind facade | 10' behind facade
Side | [image omitted; see the official code] | 3' min. | 3' min. | 3' min.
Rear | [image omitted; see the official code] | 3' min. | 3' min. | 3' min.
Dimensional Standards
15 feet maximum width for driveway curb cuts; unless required to be wider by the fire department.
Driveway curb cuts along an alley may be greater than 12 feet in width.
Parking shall meet the dimensional standards set forth in Section 17.20.060 of the Metropolitan Code.
Parking lot perimeter screening and interior planting requirements per Sections 17.24.140 and 17.24.160.
8. Voluntary Attainable Housing Incentive (RL). Buildings that comply with the requirements of the voluntary housing incentive program, as approved by Ordinance No. BL2025-1008, including any amendments, and the attainable housing requirements of Table 17.38.010.B-1 are eligible for incentives listed in Table 17.38.010.B-1. All units must be built and maintained to uniform standards in design, construction, and operations. Income-qualified units must be comparable to unrestricted units. All other District and Building Type standards apply.
Table 17.38.010.B-1
(a) Attainable Housing Requirements
Option 1 | Option 2
Set-aside | Percentage of units within the building | 10% | 5%
Income qualification | Maximum % of AMI of residents | 80% | 60%
(b) Building Form and Parking Incentives
Height | Additional stories | 2 max.
Units | No maximum unit count
Parking | No parking required for income-qualified units
Figure: 17.38.010.B(3). For M, N, O, and P, see lettered sections in 17.38.010.B Table 7 for requirements.
[image omitted; see the official code]
(Amdt. C to Ord. BL2025-1005 § 1(Exh. F), 2025; Ord. BL2025-1005 § 1(Exhs. A, F), 2025)
Source: Metropolitan Government of Nashville and Davidson County, Metropolitan Code and Charter (Municode Library, library.municode.com)URL: https://library.municode.com/tn/metro_government_of_nashville_and_davidson_county/codes/code_of_ordinances?nodeId=CD_TIT17ZO_CH17.38DESEMUMI_17.38.010.BRELIFetched: 10/28/2026
