Section 304. - Policies and standards for approval of watershed development permits, subdivision plats, lot-splits and building permits:
A. General policies. The issuance of watershed development permits and approval of subdivision plats, lot-splits and building permits shall be governed by the following general policies of the City:
1. The development shall not create a public hazard upon any property within the City or in immediately adjacent areas through the obstruction, impairment, sedimentation, blockage or alteration of the stormwater drainage system;
2. The development shall provide a sufficient stormwater drainage system for the conveyance of stormwater run-off received from upstream and from the subject property in a one hundred (100) year frequency rainstorm with due allowance having been made for full urbanization of the watershed when the quantity of stormwater may be increased; and
3. The development shall not result in additional identifiable adverse flooding of other property.
B. Specific policies and standards. The decision to deny a watershed development permit or to reject drainage plans for a subdivision plat, lot-split or building permit shall be accompanied by a statement of the reasons for such action. A development permit shall be issued if, upon review of the application therefor, it is found that the development meets and complies with the policies and standards hereinafter set out and duly adopted by the City by resolution.
C. Drainage policies and standards.
1. Policies.
a. The stormwater drainage system shall be designed to pass the stormwater run-off received from upstream and from the subject property in a one hundred (100) year frequency rainstorm under full urbanization.
b. Development shall be constructed so that it will not increase the frequency of flooding or the depth of inundation of structures.
c. Peak flows shall not be increased at any location for any storm, up to and including the one hundred (100) year storm, which will result in the inundation of unprotected structures not previously subject to inundation as a result of that same frequency storm.
d. Regulation of peak flows to allowable levels, as determined by subparagraphs (b) and (c) herein, shall be achieved by on-site or off-site storage as provided in the City drainage standards.
e. Subject to requirements for watershed development permits and of the City drainage standards, downstream conveyance may be improved to compensate for increased flows if such improvements comply with the policies of this chapter.
f. Dumping of any material into the stormwater drainage system is prohibited.
2. Standards.
a. The Director shall prepare standards for stormwater drainage facilities which shall become City drainage standards after approval by resolution by the governing body of the City.
b. All roofs, paved areas, yards, courts and courtyards, other than for one-family or two-family residential structures, shall drain into a separate storm sewer system or to an approved place of disposal.
c. In the case of one-family and two-family residential structures, stormwater may be discharged onto flat areas such as streets or lawns if drainage is provided so that the stormwater will flow away from the building.
D. Erosion and sediment control policies and standards.
1. Policies.
a. All developments shall be designed, constructed and completed in a manner which minimizes the exposure of bare earth to precipitation.
b. Development shall be constructed only if appropriate sedimentation facilities are installed and maintained throughout the construction period.
2. Standards. The policies governing watershed development, as it affects erosion and sediment control, shall be implemented by City drainage standards which shall specifically regulate the design, installation, maintenance and removal of sedimentation and erosion control facilities and structures and shall establish acceptable methods and practices for controlling soil sedimentation and erosion.
E. Regulatory flood plain area policies and standards. The Director shall, from time to time, prepare maps defining the one hundred (100) year, fully urbanized flood plains within the City. When adopted as official Regulatory Flood Plain Maps by the governing body of the City, the maps shall be made available to the public.
The provisions of this subsection shall apply to development within the identified regulatory flood plain areas graphically shown by the maps adopted by the City of Tulsa Resolution No. 13729, dated December 22, 1977, and amendments thereto.
1. Regulatory flood plain area policies.
a. Development which is dangerous to health, safety or property in times of flood or which would cause excessive increases in flood heights or velocities shall be restricted or prohibited.
b. Uses vulnerable to floods, including facilities which serve such uses, shall be protected against flood damage at the time of initial construction.
c. The alteration of natural flood plains, stream channels and watercourses shall be controlled.
d. Filling, grading, dredging and other development which may increase flood damage shall be controlled.
e. The construction of flood barriers which will unnaturally divert flood waters or which may increase flood hazards to other lands in and outside the City shall be prevented or regulated.
f. The approval or denial of a Floodway Watershed Development Permit or a Flood Plain Watershed Development Permit by the Director shall be based on the provisions of this chapter and the following relevant factors:
(1) the danger to life and property due to flooding or erosion damage;
(2) the susceptibility of the proposed facility and its contents to flood damage and the effect of such damage on the individual owner;
(3) the danger that materials may be swept onto other lands to the injury of others;
(4) the compatibility of the proposed use with existing and anticipated development;
(5) the safety of access to the property in times of flood for ordinary and emergency vehicles;
(6) the costs of providing governmental services during and after flood conditions, including maintenance and repair of streets and bridges, and public utilities and facilities such as sewer, gas, electrical and water systems;
(7) the expected heights, velocity, duration, rate of rise and sediment transport of the floodwaters expected at the site;
(8) the availability of alternative locations not subject to flooding or erosion damage for the proposed use; and
(9) the relationship of the proposed use to the comprehensive plan for that area.
2. Regulatory flood plain area standards.
a. General requirements within regulatory flood plain areas.
(1) All new construction and substantial improvements including placement of prefabricated buildings and manufactured homes shall be designed (or modified) and adequately elevated and anchored to prevent flotation, collapse or lateral movement of the structure.
(2) All new construction or substantial improvements shall be by methods and practices that minimize or eliminate flood damage.
(3) All new construction or substantial improvements shall utilize materials and utility equipment resistant to flood damage.
(4) All new and replacement water supply systems shall be floodproofed.
(5) New and replacement sanitary sewage systems shall be designed to minimize or eliminate infiltration of flood waters into the systems and discharges from the systems into flood waters.
(6) On-site waste disposal systems shall be located to avoid impairment to them or contamination from them during flooding.
(7) New structures shall be placed with their longitudinal axis parallel to the predicted direction of flow of flood waters or be placed so that their longitudinal axis are on lines parallel to those of adjoining structures.
(8) Filling or development which diminishes the flood storage capacity of any regulatory flood plain area shall be compensated for as specified in the City drainage standards.
b. Development requirements in the regulatory flood plain areas.
(1) All new construction and substantial improvements of any residential structure shall have the lowest floor, including basement, all electrical and mechanical equipment and ductwork, elevated at least one (1) foot above the regulatory flood elevation with full urbanization. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(2) All new construction and substantial improvements of any commercial, industrial or other non-residential structure shall either have the lowest floor, including basement, all electrical and mechanical equipment and ductwork, elevated at least one (1) foot above the regulatory flood elevation with full urbanization, or together with attendant utility and sanitary facilities, be floodproofed so that at least below one (1) foot above the regulatory flood level with full urbanization, the structure is watertight with walls substantially impermeable to the passage of water and with structural components having the capability of resisting hydrostatic and hydrodynamic loads and effects of buoyancy. A registered professional engineer shall submit certification to the Director that this standard regarding floodproofing has been satisfied. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(3) All new construction and substantial improvements of any structures that contain essential facilities and services necessary for emergency response and recovery, or that pose a substantial risk to the community at large in the event of failure, disruption of function, or damage by flooding, as defined in ASCE 24-14, shall have the lowest floor, including basement, all electrical and mechanical equipment and ductwork, elevated at least two (2) feet above the regulatory flood elevation with full urbanization or to the 0.2% (500-year) level of flooding whichever is higher. Alternatively the structure together with attendant utility and sanitary facilities, can be flood proofed so that at least below two (2) feet above the regulatory flood level with full urbanization or to the 0.2% (500-year) level of flooding whichever is higher, the structure is watertight with walls substantially impermeable to the passage of water. All structural components shall have the capability of resisting hydrostatic and hydrodynamic loads and effects of buoyancy. A registered professional engineer shall submit certification to the Director that this standard regarding floodproofing has been satisfied. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met
(4) All manufactured homes shall be elevated and anchored to prevent flotation, collapse or lateral movement from the regulatory flood with full urbanization. Acceptable methods of elevating and anchoring shall be set out in the City drainage standards. Methods of anchoring may include but are not limited to use of over-the-top or frame ties to ground anchors. This requirement is in addition to applicable state and local anchoring requirements for resisting wind forces.
(5) All manufactured homes to be placed in the regulatory flood plain shall have the bottom of the lowest horizontal framing member, all ductwork, electrical and mechanical equipment, elevated at least one (1) foot above the regulatory flood with full urbanization. A registered professional engineer land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(6) An evacuation plan indicating vehicular access and escape routes for manufactured home parks and subdivisions located in or surrounded by regulatory flood plain areas shall be filed with the Public Works Department and the Tulsa Area Emergency Management Agency. The owner of the manufactured home park or subdivision shall be responsible for filing vehicular access and escape routes with the Public Works Department and the Tulsa Area Emergency Management Agency and shall see that each tenant thereof has received an evacuation plan prior to the tenant's moving into the manufactured home park or subdivision.
(7) Placement of manufactured homes within the adopted regulatory floodway is prohibited except in a legally pre-existing manufactured home park or subdivision.
(8) All new construction and substantial improvements, with fully enclosed areas below the lowest floor that are subject to flooding, shall be designed to automatically equalize hydrostatic flood forces on exterior walls by allowing for the entry and exit of floodwaters. Designs for meeting this requirement must either be certified by a registered professional engineer or meet or exceed the following minimum criteria:
(a) A minimum of two (2) openings having a total net area of not less than one (1) square inch for every square foot of enclosed area subject to flooding shall be provided,
(b) The bottom of all openings shall be no higher than one (1) foot above grade; and
(c) Openings may be equipped with screens, louvers, valves or other coverings or devices, provided that they permit the automatic entry and exit of flood waters.
c. Standards for subdivision proposals in regulatory flood plain areas.
(1) All subdivision proposals shall have adequate drainage provided to reduce exposure to flood effects and shall comply with the provisions of this chapter and the City drainage standards.
(2) All subdivision proposals shall have public utilities and facilities such as sewer, gas, electrical and water systems located and constructed to minimize flood damage.
(3) Regulatory Flood Plain area delineation shall be clearly shown on all preliminary plats and final plats submitted for approval.
(4) All subdivision proposals, including manufactured home parks greater than fifty (50) lots or five (5) acres, whichever is lesser, shall show the water surface elevation of the base flood with full urbanization. When the fully urbanized base flood elevation data has not been provided, the Director shall obtain, review and reasonably utilize any base flood elevation data and floodway data available from a federal, state or other source in order to administer this provision.
d. Standards for areas of shallow flooding (AO/AH Zones).
(1) All new construction and substantial improvements of residential structures shall have the lowest floor (including basement, all electrical, mechanical, and ductwork equipment) elevated at least one (1) foot above the City determined Base Flood Elevation (BFE) or one (1) foot above the City regulatory elevation whichever is higher. Alternatively the structure together with attendant utility and sanitary facilities be designed so that below the base flood elevation the structure is watertight with walls substantially impermeable to the passage of water and with structural components having the capability of resisting hydrostatic and hydrodynamic loads and effects of buoyancy. A registered professional engineer shall submit a certification to the Director that the standards are satisfied. There shall be adequate drainage paths around structures on slopes to guide flood waters around and away from the proposed structures.
(2) The foregoing requirements of this subparagraph are minimal requirements and shall not relieve any new construction or substantial improvements from meeting and complying with additional requirements and provisions of this chapter.
3. Area of special flood hazard, policies, and standards. In all special flood hazard areas, the following policies and standards shall apply.
a. New construction, substantial improvements, or other development (including fill) shall not be approved in a special flood hazard area if it:
(1) Adversely affects the capacity of channels or floodways of any watercourse in the floodplain area to convey the regulatory flood or any flood of more frequent occurrence,
(2) Would measurably increase flood flows or flood heights or increase flood damage upon off-site properties during the occurrence of the regulatory flood or any flood of more frequent occurrence,
(3) Would individually or cumulatively, when combined with all other existing and anticipated development assuming an equal degree of encroachment for a significant reach on both sides of the stream or watercourse, increase flood levels or expose additional upstream, downstream or adjacent properties to adverse flood effects that would otherwise not be exposed to such effects due to flooding during the regulatory flood or any flood of more frequent occurrence,
(4) Increases velocities or volumes of flood waters to the extent that significant erosion of floodplain soils would occur either on the subject property or on some other property upstream or downstream, or
(5) Does not provide compensatory storage for any measurable loss of flood storage capacity.
b. Encroachments in all special flood hazard areas including fill, new construction, substantial improvements, and other development are prohibited unless the encroachments will not result in any increase of flood levels for the regulatory flood or any flood of more frequent occurrence.
c. Encroachments in the floodways including fill, new construction, substantial improvements and other development are prohibited unless the encroachments will not result in any increase of flood levels for the regulatory flood or any flood of more frequent occurrence, and certification demonstrating that the encroachments will not result in such increase in flood levels is provided by a professional registered engineer or architect.
4. Special flood hazard area notice.
a. Every owner of real property, any part of which is located in a special flood hazard area as depicted and shown on a Flood Insurance Rate Map adopted by the City, is hereby required to notify in writing every tenant of the real property of the location of the property in a designated special flood hazard area and to obtain and keep for inspection upon request by the Director or his authorized representative written acknowledgment of the receipt of the notice signed by each of the tenants.
The notice shall be given and the acknowledgment thereof obtained prior to any of the tenants taking possession of or occupying the real property or, in the case of property already rented or leased prior to the effective date of this provision, within sixty (60) days after its adoption and publication. The notice and acknowledgment shall be in a separate document and not a part of any other document, such as a lease, and it shall be substantially in the following form:
NOTICE TO TENANT OF LOCATION IN FLOOD HAZARD AREA
Notice is hereby given that the following-described real property is located within a flood hazard area as graphically shown on flood insurance rate maps as reviewed and adopted by the City of Tulsa:
(Put in legal description and address of property being leased or rented.)
Further information may be obtained from the Public Works Department of the City of Tulsa.
Dated this _______ day of _______, A.D._______.
(Signature of Owner or Agent of Owner)
ACKNOWLEDGMENT OF TENANT
The undersigned tenants of the above-described real property hereby acknowledge receipt of notice that such property is located within a flood hazard area, as graphically shown on the Flood Insurance Rate Maps adopted by the City of Tulsa.
Dated this _______ day of _______, A.D._______.
(Signature of all tenants required)
I, ___________ (name) the tenant ___________ (address) acknowledge that I have received an Evacuation Plan for ___________ manufactured home park.
(Signature of Tenant)
b. All departments, agencies, boards, commissions and employees of the City, charged with the responsibilities of issuing permits for manufactured homes or modular homes in a special flood hazard area, including the issuance of permits for hook-up of utilities to the same, shall refrain and be prohibited from issuing any such permit unless the applicant for such permit provides a copy of the notice and acknowledgment properly signed by an owner and all tenants as required herein.
c. Every owner of real property, any part of which is located in a special flood hazard area as shown on Flood Insurance Rate Maps as reviewed and adopted by the City, is required to notify in writing every purchaser of the real property of the location of the property in a designated special flood hazard area. The notice shall be given at least ten (10) days prior to closing of sale and prior to any purchaser taking possession of or occupying the real property.
5. Special flood hazard maps.
a. Establishing the areas of special flood hazard. The areas of special flood hazard identified by the Federal Emergency Management Agency in a scientific and engineering report entitled "The Flood Insurance Study for City of Tulsa, Oklahoma," dated April 15, 1982, with accompanying Flood Insurance Rate Maps and Flood Boundary-Floodway Maps (FIRM and FBFM) and any revisions thereto are adopted by reference and declared to be a part of this chapter.
(NOTE: FEMA has designated flood hazard areas [A Zones] for the City of Tulsa by the publication of Flood Boundary and Floodway Maps and by publishing a notice of final flood elevations for flood hazard areas on Flood Insurance Rate Maps. The City must adopt regulations meeting the FEMA minimum requirements for adequate flood plain management for these flood hazard areas in order to qualify for the sale of federally-subsidized flood insurance. Risk premium rates for flood insurance are charged based on the FEMA flood hazard area and flood elevation determinations. Banks, savings and loan associations, or similar institutions regulated, supervised or insured by a federal instrumentality are required by Federal law as a condition of making a loan in a flood hazard area to notify the purchaser of such flood hazards, in writing, a reasonable period of time in advance of the signing of the purchase agreement, lease or other documents involved in the transaction.)
b. FEMA map corrections and amendments.
(NOTE: The Flood Boundary and Floodway Maps and Flood Insurance Rate Maps are revised by FEMA when there is a change of community regulatory flood elevations due to changed physical conditions or where the flood elevations are technically incorrect. FEMA also issues letters of map amendment to owners or lessees of property which have been inadvertently included in a flood hazard area [A Zone].)
The Public Works Department shall review and comment on all proposed revisions to FEMA flood hazard areas and flood elevations within the City of Tulsa prior to action by FEMA on those proposals.
The Public Works Department shall submit technical data to FEMA in order to maintain the Flood Boundary and Floodway Maps and Flood Insurance Rate Maps with current data.
The revised FEMA Flood Insurance Rate Maps shall be adopted biannually after public notice by the City. Subsequent to such adoption, the Clerk shall cause copies of the FEMA maps to be delivered to and acknowledgment of receipt of such delivery to be obtained from the Mayor's Office, the Public Works Department, the Tulsa Metropolitan Area Planning Commission, the Indian Nations Council of Governments, the City-County Library, and its branches and to County Clerks in Tulsa, Osage and Rogers counties. Additional copies of the maps shall be provided to these County Clerks for distribution as information to County Engineers and Hydrologists and County Tax Assessors.
Notice shall be sent by the Public Works Department to appraisers, surveyors, realtors and lending institutions informing them that revised maps have been adopted and explaining where copies of the revised FEMA maps are located or where they may be obtained.
6. Flood plain area notice. The Public Works Department shall mail annually a notice to owners or occupants of structures within or touched by the regulatory flood plain areas, to provide information as to the status of the flood hazard for each property.
F. Drainage Sensitive Area (DSA) policies and standards. The Director shall, from time to time, prepare maps defining the one hundred (100) year, fully urbanized Drainage Sensitive Areas (DSAs) within the City. When DSAs are mapped and adopted by the governing body of the City, the maps shall be made available to the public for risk information in existing developed areas and elevation requirements for new developments.
The provisions of this subsection shall apply to development within the identified DSAs graphically shown by the maps adopted by the City of Tulsa.
1. Drainage Sensitive Area policies.
a. Development which is dangerous to health, safety or property in times of flooding or which would cause excessive increases in DSA elevations shall be restricted or prohibited.
b. Uses vulnerable to floods, including facilities which serve such uses, shall be protected against flood damage at the time of initial construction.
c. The alteration of natural DSAs and any overland flow paths shall be controlled.
d. Filling, grading, dredging and other development which may increase flood damage shall be controlled.
e. The construction of barriers which will unnaturally divert runoff waters or which may increase flood hazards to other lands in and outside the City shall be prevented or regulated.
f. The approval or denial of a Drainage Sensitive Area Watershed Development Permit by the Director shall be based on the provisions of this chapter and the following relevant factors:
(1) The danger to life and property due to flooding damage;
(2) The susceptibility of the proposed facility and its contents to flood and the effect of such damage on the individual owner;
(3) The compatibility of the proposed use with existing and anticipated development;
(4) The safety of access to the property in times of flooding for ordinary and emergency vehicles;
(5) The costs of providing governmental services during and after flood conditions, including maintenance and repair of streets and bridges, and public utilities and facilities such as sewer, gas, electrical and water systems;
(6) The expected heights, duration, and rate of rise of the floodwaters within the DSA expected at the site;
(7) The availability of alternative locations not subject to flooding damage for the proposed use; and
(8) The relationship of the proposed use to the comprehensive plan for that area.
2. Drainage Sensitive Areas standards.
a. General requirements within Drainage Sensitive Areas.
(1) All new construction including placement of prefabricated buildings and manufactured homes shall be designed (or modified) and adequately elevated and anchored to prevent flotation, collapse or lateral movement of the structure.
(2) All new construction shall be by methods and practices that minimize or eliminate flood damage.
(3) All new construction shall utilize materials and utility equipment resistant to flood damage.
(4) All new and replacement water supply systems shall be floodproofed.
(5) New and replacement sanitary sewage systems shall be designed to minimize or eliminate infiltration of stormwater into the systems and discharges from the systems into the DSA.
(6) On-site waste disposal systems shall be located to avoid impairment to them or contamination from them during flooding.
(7) Filling or development which diminishes the flood storage capacity of any DSA shall be compensated for as specified in the City drainage standards.
Compensatory storage calculations for DSAs shall be determined for all flood depths.
b. Development requirements in the Drainage Sensitive Areas.
(1) All new construction of any residential structure shall have the lowest floor, including basement, all electrical and mechanical equipment and ductwork, elevated at least one (1) foot above the DSA elevation with full urbanization. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(2) All new construction of any commercial, industrial or other non-residential structure shall either have the lowest floor, including basement, all electrical and mechanical equipment and ductwork, elevated at least one (1) foot above the DSA elevation with full urbanization, or together with attendant utility and sanitary facilities, be floodproofed so that at least below one (1) foot above the DSA elevation with full urbanization, the structure is watertight with walls substantially impermeable to the passage of water and with structural components having the capability of resisting hydrostatic and hydrodynamic loads and effects of buoyancy. A registered professional engineer shall submit certification to the Director that this standard regarding floodproofing has been satisfied. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(3) All new construction of any structures that contain essential facilities and services necessary for emergency response and recovery, or that pose a substantial risk to the community at large in the event of failure, disruption of function, or damage by flooding, as defined in ASCE 24-14, shall have the lowest floor, including basement, all electrical and mechanical equipment and ductwork, elevated at least two (2) feet above the DSA elevation with full urbanization. Alternatively the structure together with attendant utility and sanitary facilities, can be flood proofed so that at least below two (2) feet above the regulatory flood DSA elevation with full urbanization, the structure is watertight with walls substantially impermeable to the passage of water. All structural components shall have the capability of resisting hydrostatic and hydrodynamic loads and effects of buoyancy. A registered professional engineer shall submit certification to the Director that this standard regarding floodproofing has been satisfied. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(4) All manufactured homes shall be elevated and anchored to prevent flotation, collapse or lateral movement from the DSA elevation with full urbanization. Acceptable methods of elevating and anchoring shall be set out in the City drainage standards. Methods of anchoring may include but are not limited to use of over-the-top or frame ties to ground anchors. This requirement is in addition to applicable state and local anchoring requirements for resisting wind forces.
(5) All manufactured homes to be placed in the DSA shall have the bottom of the lowest horizontal framing member, all ductwork, electrical and mechanical equipment, elevated at least one (1) foot above the DSA elevation with full urbanization. A registered professional engineer or land surveyor shall submit a certification to the Director that the elevation requirement has been met.
(6) Placement of manufactured homes within the DSA is prohibited except in a legally pre-existing manufactured home park or subdivision.
(7) All new construction and substantial improvements, with fully enclosed areas below the lowest floor that are subject to flooding, shall be designed to automatically equalize hydrostatic flood forces on exterior walls by allowing for the entry and exit of floodwaters. Designs for meeting this requirement must either be certified by a registered professional engineer or meet or exceed the following minimum criteria:
(a) A minimum of two (2) openings having a total net area of not less than one (1) square inch for every square foot of enclosed area subject to flooding shall be provided,
(b) The bottom of all openings shall be no higher than one (1) foot above grade; and
(c) Openings may be equipped with screens, louvers, valves or other coverings or devices, provided that they permit the automatic entry and exit of floodwaters.
c. Standards for subdivision proposals in Drainage Sensitive Areas.
(1) All subdivision proposals shall have adequate drainage provided to reduce exposure to flood effects and shall comply with the provisions of this chapter and the City drainage standards.
(2) All subdivision proposals shall have public utilities and facilities such as sewer, gas, electrical and water systems located and constructed to minimize flood.
(3) DSA delineation shall be clearly shown on all preliminary plats and final plats submitted for approval.
(4) All subdivision proposals, including manufactured home parks greater than fifty (50) lots or five (5) acres, whichever is lesser, shall show the water surface elevation of the DSA with full urbanization.
3. Drainage Sensitive Area notice.
a. Every owner of real property, any part of which is located in a DSA as depicted and shown on the City of Tulsa regulatory flood map adopted by the City, is hereby required to notify in writing every tenant of the real property of the location of the property in a designated DSA and to obtain and keep for inspection upon request by the Director or his authorized representative written acknowledgment of the receipt of the notice signed by each of the tenants.
The notice shall be given, and the acknowledgment thereof obtained prior to any of the tenants taking possession of or occupying the real property or, in the case of property already rented or leased prior to the effective date of this provision, within sixty (60) days after its adoption and publication. The notice and acknowledgment shall be in a separate document and not a part of any other document, such as a lease, and it shall be substantially in the form described in Section 304.E.4:
(Ord. Nos. 16959, 17173, 17285, 17466, 18838; Ord. No. 23924, § 1, 6-6-2018; Ord. No. 25244, § 2, 1-31-2024; Ord. No. 25399, §§ 2, 3, 9-18-2024)